Homemade AR with glue
- WLJ
- KAC Member
- Posts: 30625
- Joined: Sat Mar 03, 2012 8:55 pm
- Location: Epsilon Eridani System
- Has liked: 11 times
- Been liked: 110 times
Re: Homemade AR with glue
When do the barrel molds come out?
There are criminals among us who are both homicidal and incorrigible. Their parents took a shot at civilizing them and failed. Their school teachers took a shot at them and failed. The odds are overwhelming that government welfare programs and penal institutions took a shot at them and failed. If it ever becomes your turn to take a shot at them, don’t fail.
- ssracer
- KAC Member
- Posts: 13700
- Joined: Sat Mar 03, 2012 8:24 pm
- Location: KY
- Has liked: 1 time
- Been liked: 56 times
- Contact:
-
- KAC Member
- Posts: 800
- Joined: Sat Feb 09, 2013 10:03 pm
- Location: henderson/louisville,ky
- Has liked: 0
- Been liked: 0
Homemade AR with glue
After you buy the molds you can build 5 for 129
I honestly don't see much difference between this and any other polymer lower. Other than the quality of polymer.
I will Still stick to my 39.99 Anderson lowers.
I honestly don't see much difference between this and any other polymer lower. Other than the quality of polymer.
I will Still stick to my 39.99 Anderson lowers.
Ky CCDW Instructor
-
- KAC Member
- Posts: 6383
- Joined: Sat Mar 03, 2012 8:48 pm
- Location: Metro Louisville
- Has liked: 3 times
- Been liked: 15 times
- Contact:
Re: Homemade AR with glue
This is not a polymer lowerken6881 wrote:After you buy the molds you can build 5 for 129
I honestly don't see much difference between this and any other polymer lower. Other than the quality of polymer.
I will Still stick to my 39.99 Anderson lowers.
It is a epoxy glue- a casting resin
Plastic lower is different material
Last edited by guncrank1 on Thu May 05, 2016 6:43 pm, edited 1 time in total.
-
- Global Mod
- Posts: 12053
- Joined: Sat Mar 03, 2012 8:50 pm
- Location: Louisville
- Has liked: 20 times
- Been liked: 22 times
Re: Homemade AR with glue
I bet his mom is pissed at the cleanup from all the attempts in her basement.kokopelli wrote:Guy on Arfcom came up with this
Re: Homemade AR with glue
I have tried to make small parts with similar type stuff before...the bubbles are the devil. Outside edges can be severely affected by them. Tough to make...is saying it lightly. Lots of experience needed which means lots of errors being made which equals money lost.
- Wyldman
- KAC Member
- Posts: 6984
- Joined: Sat Mar 03, 2012 8:01 pm
- Location: Spring, TX
- Has liked: 0
- Been liked: 0
Re: Homemade AR with glue
A vibratory table would almost be mandatory to work out air bubbles. I imagine shrinkage could be an issue, too. Kind of hard on precision specs...
Crush, kill, mangle, maim, destroy.
Crush, kill, mangle, maim, destroy.
IN GOD WE TRUST
"That boy's paradigm don't always add up to four nickels...."
"That boy's paradigm don't always add up to four nickels...."
- ssracer
- KAC Member
- Posts: 13700
- Joined: Sat Mar 03, 2012 8:24 pm
- Location: KY
- Has liked: 1 time
- Been liked: 56 times
- Contact:
Re: Homemade AR with glue
Wyldman wrote:A vibratory table would almost be mandatory to work out air bubbles. I imagine shrinkage could be an issue, too. Kind of hard on precision specs...
Crush, kill, mangle, maim, destroy.