Kentucky Armory Club

Post by **adayton** » Mon Apr 04, 2016 2:38 pm

ssracer wrote:
adayton wrote:
ssracer wrote:Nice! And yes, the firing pin works the same on my new frontier bolt
So Sean,
Are you experiencing some misfires due to the way the bolt is designed? If not, which FCG are you using?
Thanx,
Allan
I had no feed or fire issues with mine at all. Shot mostly freedom munitions reloads and a few HP's from my carry mag. Mine is just running a milspec FCG with the hammer, trigger and sear all titanium nitride coated.

OK... As soon as I get to the range, I will report back here what I find with the Hiperfire 24 trigger... If that doesn't work, I'll throw an EDT or Milspec AR FCG ...
Thanx,
Allan

Post by **adayton** » Wed Apr 06, 2016 11:01 am

So I got to take my 9mm AR 'pistol' to Open Range yesterday afternoon... I ran 10 or so rounds through it from each stick mag with no issues ... Then I put the original firing pin spring back in it... It ran everything else that I could run through it ... I brought mostly 147 grain ammo as I plan on using it mainly suppressed ... I had one FTFire ... and I attribute that to the bolt not going into full battery that one time... I lubed it up a bit as it was quite dry and didn't have any other issues at all ...
Quite pleased with it in fact.

Post by **RecoilSensitive** » Sat Apr 09, 2016 8:47 pm

I am ordering a lower from joebob this week. Lowers will be sent to Allan for transfer. If we get 2 more on buy we can save some $$$ anyone else?

Post by **shaggy1392** » Fri Apr 15, 2016 6:21 pm

Got an approved form 1 back today. Now I need an upper.

Post by **Gunsmokin** » Fri Apr 15, 2016 6:59 pm

shaggy1392 wrote:Got an approved form 1 back today. Now I need an upper.

Nice! Glad it finally came through.

Post by **shaggy1392** » Fri Apr 15, 2016 8:08 pm

Gunsmokin wrote:
shaggy1392 wrote:Got an approved form 1 back today. Now I need an upper.
Nice! Glad it finally came through.

Me too. My original was actually disapproved because I made an error when efiling so I had to submit a new form. It got approved in about 2 hours.

Post by **bigelowe** » Fri Apr 15, 2016 8:43 pm

RecoilSensitive wrote:I am ordering a lower from joebob this week. Lowers will be sent to Allan for transfer. If we get 2 more on buy we can save some $$$ anyone else?

Show me which one your looking at, I may be interested.

Post by **Gunsmokin** » Sat Apr 16, 2016 7:47 am

shaggy1392 wrote:
Gunsmokin wrote:
shaggy1392 wrote:Got an approved form 1 back today. Now I need an upper.
Nice! Glad it finally came through.
Me too. My original was actually disapproved because I made an error when efiling so I had to submit a new form. It got approved in about 2 hours.

What sort of error? Thinking it may be of help to others to know what gets things kicked back. Especially, if it was anything more than omitting info from a required box. Thx.

Post by **Gunsmokin** » Sat Apr 16, 2016 7:52 am

Should be wrapping up my 9 sbr today. Tracking for my package from JBO says it is scheduled to deliver today.

Post by **shaggy1392** » Sat Apr 16, 2016 10:25 am

Gunsmokin wrote:
shaggy1392 wrote:
Gunsmokin wrote:
shaggy1392 wrote:Got an approved form 1 back today. Now I need an upper.
Nice! Glad it finally came through.
Me too. My original was actually disapproved because I made an error when efiling so I had to submit a new form. It got approved in about 2 hours.
What sort of error? Thinking it may be of help to others to know what gets things kicked back. Especially, if it was anything more than omitting info from a required box. Thx.

My lower is a cmmg mk9. When I was selecting the type from the drop box the first thing I saw was ar15mk9 so I selected that. Turns out that if you keep scrolling down they have mk-9 and mk9 listed too and it has to match exactly what is engraved on the receiver. I had to refile and pay for the tax stamp again. Now I'm waiting on a refund from my original, but atleast I have an approved form in hand.

Post by **Gunsmokin** » Sat Apr 16, 2016 1:41 pm

Gotcha.

Post by **Bama** » Sat Apr 16, 2016 6:02 pm

For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk

http://www.youtube.com/user/ssracer02 · Post by **ssracer** » Sat Apr 16, 2016 6:51 pm

Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk

i should CC my build...it is a pistol....lol

Post by **bigelowe** » Sat Apr 16, 2016 7:42 pm

ssracer wrote:
Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk
i should CC my build...it is a pistol....lol

I want one see the holster. Lol

http://www.youtube.com/user/ssracer02 · Post by **ssracer** » Sat Apr 16, 2016 9:37 pm

bigelowe wrote:
ssracer wrote:
Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk
i should CC my build...it is a pistol....lol

I want one see the holster. Lol

BAMA!!!!

Post by **bigelowe** » Sat Apr 16, 2016 9:49 pm

ssracer wrote:
bigelowe wrote:
ssracer wrote:
Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk
i should CC my build...it is a pistol....lol

I want one see the holster. Lol
BAMA!!!!

Do they make kydex sheets that big??????? Haha

Post by **Bama** » Sat Apr 16, 2016 9:51 pm

bigelowe wrote:
ssracer wrote:
bigelowe wrote:
ssracer wrote:
Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk
i should CC my build...it is a pistol....lol

I want one see the holster. Lol
BAMA!!!!

Do they make kydex sheets that big??????? Haha

All they way up to a 4'x8' sheet!

Send it down SS, may take me a while to dial in the holster.

Post by **Gunsmokin** » Sat Apr 16, 2016 10:32 pm

Well, crap! I got issues with my build. Doesn't look like this thing is going to get much action until I either get my can or buy a slightly longer barrel. The 4.5" barrel with a pig can is just about a half inch shy of the end of the handguard. Won't be an issue with the suppressor, but I feel like it needs to be tested and ran some before I stick the can on it. Thinking about just getting a 5.5" or 6" barrel for it. I also need to get sights or an optic for it and a couple OEM Glock mags. Not getting a good feeling from the cheapo mags.

Post by **Gunsmokin** » Sat Apr 16, 2016 10:33 pm

http://www.youtube.com/user/ssracer02 · Post by **ssracer** » Sat Apr 16, 2016 11:53 pm

The pig will still send all the blast pressure forward...you might be ok

http://www.youtube.com/user/ssracer02 · Post by **ssracer** » Sat Apr 16, 2016 11:54 pm

Bama wrote:
bigelowe wrote:
ssracer wrote:
bigelowe wrote:
ssracer wrote:
Bama wrote:For those attending NRAAM, QTRC10 will be there.

Sent from my iPhone using Tapatalk
i should CC my build...it is a pistol....lol

I want one see the holster. Lol
BAMA!!!!

Do they make kydex sheets that big??????? Haha
All they way up to a 4'x8' sheet!

Send it down SS, may take me a while to dial in the holster.

4'x8'....damn!!

Post by **Gunsmokin** » Sun Apr 17, 2016 8:11 am

ssracer wrote:The pig will still send all the blast pressure forward...you might be ok

Might be ok?!? I think if I test it, I'll just remove the handguard.

Post by **Niceguy** » Sun Apr 17, 2016 9:04 am

Gunsmokin wrote:Well, crap! I got issues with my build. Doesn't look like this thing is going to get much action until I either get my can or buy a slightly longer barrel. The 4.5" barrel with a pig can is just about a half inch shy of the end of the handguard. Won't be an issue with the suppressor, but I feel like it needs to be tested and ran some before I stick the can on it. Thinking about just getting a 5.5" or 6" barrel for it. I also need to get sights or an optic for it and a couple OEM Glock mags. Not getting a good feeling from the cheapo mags.

If it's 1/2x28 thread, we can meet up sometime and you can test it suppressed...

Post by **Gunsmokin** » Sun Apr 17, 2016 9:18 am

Niceguy wrote:
Gunsmokin wrote:Well, crap! I got issues with my build. Doesn't look like this thing is going to get much action until I either get my can or buy a slightly longer barrel. The 4.5" barrel with a pig can is just about a half inch shy of the end of the handguard. Won't be an issue with the suppressor, but I feel like it needs to be tested and ran some before I stick the can on it. Thinking about just getting a 5.5" or 6" barrel for it. I also need to get sights or an optic for it and a couple OEM Glock mags. Not getting a good feeling from the cheapo mags.
If it's 1/2x28 thread, we can meet up sometime and you can test it suppressed...

Not. It's the goofy 1/2x36 thread.

Post by **Niceguy** » Sun Apr 17, 2016 9:21 am

That sucks... I got a 1/2x28 barrel from QC10. Pricey and rarely in stock though. If you eventually are going to have to get an adapter any, you're still welcome to try it. I just don't have one.

Kentucky Armory Club

AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Re: AR9

Login • Register