my 10/22 1 week build up
- etownguy
- KAC Member
- Posts: 1412
- Joined: Fri Mar 09, 2012 9:08 am
- Location: Cecilia
- Has liked: 0
- Been liked: 5 times
my 10/22 1 week build up
I got rid of the 15-22 to build something a little more accurate and still semi-auto. this is what I have come up with.
stock 10/22 carbine wood stock 18.5" barrel
added parts:
Volquartsen: target hammer, trigger spring, auto bolt release, bolt charge handle/recoil spring, recoil buffer, x-act edge extractor and spring
Power customs extended mag. release
Adam's & Bennett .920 Bull Barrel 18" steel
Tactical Solutions V-Block (holds up the heavy barrel no droop)
Hogue overmolded .920 stock
Talley 1 piece scope mounts
Nikon Prostaff rimfire BDC 150
Worked over:
beveled the rear the bolt for better hammer reset and polished the whole thing
removed all paint from the inside of the receiver and did a half ass polish job smoother bolt movement
polished sear
only thing I still need is a sling mounted bipod.
Still have not shot it that'll come later today or tomorrow.
even if it shoots like shit it still looks awesome to me!
stock 10/22 carbine wood stock 18.5" barrel
added parts:
Volquartsen: target hammer, trigger spring, auto bolt release, bolt charge handle/recoil spring, recoil buffer, x-act edge extractor and spring
Power customs extended mag. release
Adam's & Bennett .920 Bull Barrel 18" steel
Tactical Solutions V-Block (holds up the heavy barrel no droop)
Hogue overmolded .920 stock
Talley 1 piece scope mounts
Nikon Prostaff rimfire BDC 150
Worked over:
beveled the rear the bolt for better hammer reset and polished the whole thing
removed all paint from the inside of the receiver and did a half ass polish job smoother bolt movement
polished sear
only thing I still need is a sling mounted bipod.
Still have not shot it that'll come later today or tomorrow.
even if it shoots like shit it still looks awesome to me!
-
- Founding Father
- Posts: 7009
- Joined: Sat Mar 03, 2012 7:40 pm
- Has liked: 3 times
- Been liked: 0
Re: my 10/22 1 week build up
Looks good...........what did you use to remove the paint from inside of receiver??
***I like that mag release
***I like that mag release
"All that is necessary for the triumph of evil is that good men do nothing."(Edmund Burke)
- Ian
- KAC Member
- Posts: 2447
- Joined: Sun Mar 04, 2012 4:11 pm
- Location: Louisville, KY
- Has liked: 0
- Been liked: 0
Re: my 10/22 1 week build up
Looks nice, same thoughts on paint removal?
"Not all men seek rest and peace; some are born with the spirit of the storm in their blood, restless harbingers of violence and bloodshed, knowing no other path." Robert Howard
- justang1997
- KAC Member
- Posts: 3169
- Joined: Sun Mar 04, 2012 12:59 pm
- Location: Vine Grove
- Has liked: 0
- Been liked: 0
- etownguy
- KAC Member
- Posts: 1412
- Joined: Fri Mar 09, 2012 9:08 am
- Location: Cecilia
- Has liked: 0
- Been liked: 5 times
Re: my 10/22 1 week build up
http://www.automotivetouchup.com/sandpa ... f-pad.aspx
the prep pad is like this.. it is equivalent to 600 grit I think but takes off paint very well.
other two came in the polishing kit I bought from lowes for the dremel
the prep pad is like this.. it is equivalent to 600 grit I think but takes off paint very well.
other two came in the polishing kit I bought from lowes for the dremel
- etownguy
- KAC Member
- Posts: 1412
- Joined: Fri Mar 09, 2012 9:08 am
- Location: Cecilia
- Has liked: 0
- Been liked: 5 times
Re: my 10/22 1 week build up
Quite satisfied with the results! I layed prone at 30 yards with a bi-pod to sight it in that target says M-22 Sight this was 25 shots the far out round were me adjusting the scope into place. Everything else was at a measured 50 yards in a rest on a cheap plastic table that would flex if I leaned on it. This will be the last time I use these targets as seeing the black crosshairs on the black target really strains my eyes and it all gets blurry.
VV I did not adjust anything the Velocitors just shot this much higher. VV
VV I did not adjust anything the Velocitors just shot this much higher. VV
- Murgatroy
- Posts: 42
- Joined: Tue Mar 20, 2012 8:53 pm
- Location: Shelbyville, Kentucky
- Has liked: 0
- Been liked: 0
Re: my 10/22 1 week build up
I like the simplicity of it.
I am currently torn between the Archangel target stock which is getting decent reviews and the Hogue.
Have you tried other stocks to compare to the Hogue?
I am currently torn between the Archangel target stock which is getting decent reviews and the Hogue.
Have you tried other stocks to compare to the Hogue?
Yoda for President
- justang1997
- KAC Member
- Posts: 3169
- Joined: Sun Mar 04, 2012 12:59 pm
- Location: Vine Grove
- Has liked: 0
- Been liked: 0
Re: my 10/22 1 week build up
I really doubt you would shrink your groups any. The non wood stocks will just keep your zero better as the temps and humidity and what not will cause the wood to shift your point of impact.
- etownguy
- KAC Member
- Posts: 1412
- Joined: Fri Mar 09, 2012 9:08 am
- Location: Cecilia
- Has liked: 0
- Been liked: 5 times
my 10/22 1 week build up
I am loving this gun got a chance to do some 200+ yard shooting this weekend. After a bunch of cranking on the elevation it was dead on. I was semi reliably hitting a metal fence post at 200 yards.